WPS/PQR/WPQ:A Welding Procedure Specification (WPS) is a formal written document describing welding procedures, which provides direction to the welder or welding operators for making sound and quality production welds as per the codes & Standard r.
- Wps Wpqr Welding Procedures
- Welding Wps And Pqr
- Wps Welding Procedure Specification Pdf
- Wps Wpqr Welding Procedure Definition
A Welding Procedure Qualification Record (WPQR) documents the variables and the results of testing. Weld procedure qualification testing is usually destructive. Material welded under a WPS is placed under force until the weld or surrounding material gives way. The WPS is a proven process of welding and is important to ensure welding operators in the field are maintaining the same, required standards across the board. The mechanical properties of a weld cannot be verified in production welds after welding so control of the welding process using a WPS is critical.
Guide to understanding Welding Procedure Specification (WPS), Procedure Qualification Record (PQR), and Welder Performance Qualification Record (WPQR)
By Nagesh Goel, Director
CONTENTS
- Introduction
- What is Welding Procedure Specification (WPS)?
- What is Procedure Qualification Record (PQR)?
- What information should they include?
- What is a Prequalified WPS?
- What are SWPSs?
- What is Welder Performance Qualification Record (WPQR)?
- Acceptance Standards.
- Documentation
- PQR/ WPQR Testing.
- Weld Inspection and Testing.
Introduction
Welding requires skill. Determining “how to weld” requires knowledge regarding the materials being welded and welding process, among numerous other factors. Because of huge number of variables involved, the knowledge of the welding engineer and the skill of the welder need to be validated by a series of tests. All this information is documented on Welding Procedure Specification (WPS), Procedure Qualification Record (PQR), Welding Procedure Qualification Record (WPQR), and associated Test Reports.
What is Welding Procedure Specification (WPS)?
A WPS is a document that describes how welding is to be carried out in production. Its purpose is to aid the planning and quality control of the welding operation. They are recommended for all welding operations and most application codes and standards make them mandatory.
What is Procedure Qualification Record (PQR)?
A PQR is required when it is necessary to demonstrate that your company has the ability to produce welds possessing the correct mechanical and metallurgical properties.
A welding procedure must be qualified in accordance with the requirements of an appropriate welding procedure standard, such as ASME Sec IX, as follows:
- Produce a welding procedure specification (WPS) as stated above.
- Weld a test piece in accordance with the requirements of your specification. The joint set up, welding and visual examination of the completed weld should be witnessed by a certified welding inspector such as an AWS certified CWI or an Inspection Body. The details of the test such as the welding current, pre-heat etc., must be recorded during the test.
- Once the welding is complete the test piece must be subject to destructive and non destructive examination such as radiography and mechanical tests as defined by the welding procedure standard. This work must be carried out in a qualified laboratory but the Inspection Body may require witnessing the tests and viewing any radiographs.
- If the test is successful you or the test body completes the appropriate documents which the test body’s surveyor signs and endorses.
Wps Wpqr Welding Procedures
What information should they include?
Sufficient details to enable any competent person to apply the information and produce a weld of acceptable quality. The amount of detail and level of controls specified on a WPS is dependant on the application and criticality of the joint to be welded.
For most applications the information required is generally similar to that recorded on a Procedure Qualification Record (PQR), except that ranges are usually permitted on thicknesses, diameters, welding current, materials, joint types etc.
If a WPS is used in conjunction with an approved procedure qualification record (PQR) then the ranges stated should be in accordance with the approval ranges permitted by the PQR.
Welding Wps And Pqr
However careful consideration should be given to the ranges specified to ensure they are achievable, so that these ranges represent good welding practice.
What is a Prequalified WPS?
Some codes, such as AWS D1.1, allow “Prequalified WPS”, whereby it is established that the WPS written per code will produce welds with correct mechanical and metallurgical properties. It is not necessary to prepare a PQR in such cases. However, the pre-qualified WPS have a specified range of parameters under which the weld must be produced. When welding variables fall outside these ranges, a WPS with supporting PQR must be prepared.
What are SWPSs?
In an effort to standardize and harmonize the process of WPS approvals, AWS started writing “Standard Welding Procedure Specifications (SWPSs)” with input from the pioneers and experts in the welding industry. An extensive testing program was undertaken whereby; these SWPSs were then supported by numerous PQRs.
When the use of SWPSs is permitted by referencing code section, your company does not have to perform one or more procedure qualification tests. You can simply purchase the applicable SWPS for unlimited intra-company use from the American Welding Society (www.aws.org).
What is Welder Performance Qualification Record (WPQR)?
Once the procedure is approved it is necessary to demonstrate that all your welders working to it have the required knowledge and skill to put down a clean sound weld. If the welder has satisfactorily completed the procedure test then he is automatically approved but each additional welder must be approved by completing an approval test to an appropriate standard such as ASME Sec IX as follows:
- Complete a weld test as stated above. The test should simulate production conditions and the welding position should be the position that the production welds are to be made in or one more severe.
- For maximum positional approval a pipe inclined at 45 degrees (referred to as the 6G position) approves all positions except vertical down.
- Test the completed weld in accordance with the relevant standard to ensure that the weld is clean and fully fused.
- For a butt weld this is normally a visual examination followed by radiography or bend tests.
- Once the test is completed the necessary forms have to be completed by you or the test body and signed by the test body’s surveyor.
- Note that any changes that require a new welding procedure (WPS) may also apply to the welders approval, refer to the referencing code/ standard for precise details.
Acceptance Standards
In general welds must show a neat workman like appearance. The root must be fully fused along the entire length of the weld, the profile of the cap should blend in smoothly with the parent material and the weld should be significantly free from imperfections. Reference should be made to the acceptance standard for precise details.
Documentation
The necessary documents for a successful Welding Program are as follows:
- Welding Procedure Specification (WPS), Procedure Qualification Record (PQR), Independent Laboratory Test Report for the PQR, Welder Performance Qualification Record (WPQR), and Independent Laboratory Test Report for the WPQR; OR
- Pre-qualified Welding Procedure Specification (Applicable to some Codes only), Welder Performance Qualification Record (WPQR), and Independent Laboratory Test Report for the WPQR; OR
- Code adopted Standard Welding Procedure Specification (SWPS), Welder Performance Qualification Record (WPQR), and Independent Laboratory Test Report for the WPQR
PQR/ WPQR Testing
The following tests by Independent Test Laboratory may be required on your PQR and WPQR Coupons:
- Weld Visual Examination by a AWS Certified Welding Inspector
- Bend Test
- Hardness Test
- Transverse Tensile Test
- All Weld Metal Tensile Test
- Charpy Impact Test
- Weld Metal Chemical Analysis
- Macroetch Test
- Torque Test
- Peel Test
- Nick Break Test
- Radiography Test
- Ultrasonic Test
Weld Inspection and Testing
In addition to the above, you may require independent inspection of the welds by the following qualified personnel:
Wps Welding Procedure Specification Pdf
- Visual Inspection by AWS Certified Welding Inspector (CWI)
- Radiographic Testing by Level II personnel certified as per SNT-TC-1A
- Ultrasonic Testing by Level II personnel certified as per SNT-TC-1A
- Magnetic Particle Testing by Level II personnel certified as per SNT-TC-1A
- Penetrant Testing by Level II personnel certified as per SNT-TC-1A
Wps Wpqr Welding Procedure Definition
AEIS can perform the above tests at your facility or at our laboratory.